Network models by region
Europe
Name
|
Version
|
Year
|
Region
|
Num. Substations or Buses
|
Num. Lines
|
Contains
|
Downloadable
|
Licence
|
SciGrid
|
0.1
|
2015
|
Germany, but in principle whole world
|
479
|
765
|
Topology, Impedances
|
Yes
|
Apache Licence, Version 2.0
|
Bialek European Model
|
2
|
2013
|
Continental Europe
|
1494 buses
|
2322
|
Topology, Impedances, Loads, Generators
|
Yes
|
Unclear
|
National Grid ETYS 2014 Model
|
|
2014
|
Great Britain
|
365
|
316
|
Topology, Impedances, Loads, Generators
|
Yes
|
Unclear
|
Austrian Power Network Grid
|
|
2015
|
Austria
|
|
~100
|
Topology, Impedances
|
Yes
|
Unclear
|
SciGrid
SciGrid is a project started in 2014 and running for three years to develop an open and free model of the European transmission network. It is carried out by NEXT ENERGY - EWE Research Centre for Energy Technology, an independent non-profit institute at the University of Oldenburg, Germany, and funded by the German Ministry of Education.
Bialek European Model
The 2nd version of the Bialek European Model is downloadable as an Excel file and in the format of the proprietary modelling software PowerWorld.
The 1st version was released in 2002-2004 and is no longer available (see Archive mirror. The 1st version did not contain the Balkans region.
National Grid Model
National Grid Electricity Ten Year Statement 2014 Model
Austrian Power Network Grid Model
Austrian Power Network Grid
Global
IRENA
Other lists of network models
Enipedia list
Edinburgh University list
Free software for load-flow or flow optimisation
PyPower in Python
PowerGAMA in Python
MATPOWER in Matlab or Octave
OpenDSS in Pascal?
PSAT in Matlab or Octave
Other lists of load-flow software
http://www.openelectrical.org/wiki/index.php?title=Power_Systems_Analysis_Software
https://nkloc.wordpress.com/2011/11/11/power-system-simulation-software-list/
Typical transmission line technical parameters
European 50 Hz transmission
The European transmission system is operated at 50 Hz.
On the continent voltages are typically 220 kV or 380 kV (sometimes quoted as 400 kV, since network operators often run their grid above nominal voltage to reduce network losses).
220 kV lines are typically configured with a bundle of 2 wires per phase with wires of cross-section Al/St 240/40.
380 kV lines are typically configured with a bundle of 4 wires per phase with wires of cross-section Al/St 240/40.
We now list the impedances for the lumped pi model of the transmission lines.
Electrical properties for single circuits
Voltage level (kV)
|
Type
|
Conductors
|
Series resistance (Ohm/km)
|
Series inductance (Ohm/km)
|
Shunt capacitance (nF/km)
|
Current limit (A)
|
220
|
Overhead line
|
2-wire-bundle Al/St 240/40
|
0.06
|
0.301
|
12.5
|
1290
|
380
|
Overhead line
|
4-wire-bundle Al/St 240/40
|
0.03
|
0.246
|
13.8
|
2580
|
In the table the current limit is calculated as 645 A per wire at an outside temperature of 20 degrees Celsius.
Sources for the electrical parameters:
Oeding and Oswald Elektrische Kraftwerke und Netze, 2011, Chapter 9
See also comparable parameters in the DENA Distribution Network, 2012, Table 5.6 and KIT Electrical Parameters Reading Sample, 2013.
Combining electrical parameters for multiple circuits
In the table above, the impedances are quoted for a single circuit. The resistance and inductances are in series, so decrease proportional to the number of circuits (roughly - the geometry changes mean the series inductances is slightly modified). Similarly the capacitance is in shunt so increases proportional to the number of circuits (again, roughly because of changing geometry).